NOKIA OLT configuration
NOKIA OLT configuration
leg:isadmin>configure>router# mpls
leg:isadmin>configure>router>mpls# info
———————————————-
shutdown
interface “system”
no shutdown
exit
———————————————-
leg:isadmin>configure>router>mpls# no shutdown
leg:isadmin># show equipment slot
================================================================================
slot table
================================================================================
slot |actual-type|enabled|error-status |availability |restrt-cnt
———–+———–+——-+———————-+————-+———–
acu:1/1 ngfc-f no no-planned-board available 0
nt-a fant-f yes no-error available 0
nt-b fant-f no no-planned-board available 0
lt:1/1/5 fglt-b no no-planned-board available 0
lt:1/1/6 fglt-b no no-planned-board available 0
lt:1/1/7 empty no no-error not-installed 0
lt:1/1/8 empty no no-error not-installed 0
vlt:1/1/63 empty no no-error not-installed 0
vlt:1/1/64 empty no no-error not-installed 0
——————————————————————————–
slot count : 9
================================================================================
leg:isadmin>#
leg:isadmin># configure port nt-a:xfp:1 ethernet speed 1000 # configure Uplink Port #
leg:isadmin># configure port nt-a:xfp:1 no shutdown
leg:isadmin># show port #Check port interfaces #
====================================================================
Ports on NT
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
nt:vp:1 Up Yes Up 1518 1518 – accs dotq vport
nt:mc:1 Up Yes Up 1518 1518 – accs dotq vport
====================================================================
Ports on NT-A
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
nt-a:eth:1 Down No Down 9212 9212 – accs dotq xcme
nt-a:xfp:1 Up No Down 9212 9212 – accs dotq gige
nt-a:xfp:2 Down No Down 9212 9212 – accs dotq gige
nt-a:xfp:3 Down No Down 9212 9212 – accs dotq gige
nt-a:xfp:4 Down No Down 9212 9212 – accs dotq gige
====================================================================
Ports on NT-B
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
nt-b:eth:1 Down No Down 9212 9212 – accs dotq xcme
nt-b:xfp:1 Down No Down 9212 9212 – accs dotq gige
nt-b:xfp:2 Down No Down 9212 9212 – accs dotq gige
nt-b:xfp:3 Down No Down 9212 9212 – accs dotq gige
nt-b:xfp:4 Down No Down 9212 9212 – accs dotq gige
====================================================================
Ports on LT
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
lt:1/1/5 Up Yes Up 9212 9212 – accs dotq lt
lt:1/1/6 Up Yes Up 9212 9212 – accs dotq lt
lt:1/1/7 Up No Down 9212 9212 – accs dotq lt
lt:1/1/8 Up No Down 9212 9212 – accs dotq lt
====================================================================
Ports on NT-A
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
nt-a:AI:1 Down No Down 9212 9212 – accs dotq gige
====================================================================
Ports on NT-B
====================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port
Id State State MTU MTU Bndl Mode Encp Type
——————————————————————–
nt-b:AI:1 Down No Down 9212 9212 – accs dotq gige
====================================================================
leg:isadmin># show equipment slot
================================================================================
slot table
================================================================================
slot |actual-type|enabled|error-status |availability |restrt-cnt
———–+———–+——-+———————-+————-+———–
acu:1/1 ngfc-f no no-planned-board available 0
nt-a fant-f yes no-error available 0
nt-b fant-f no no-planned-board available 0
lt:1/1/5 fglt-b no no-planned-board available 0
lt:1/1/6 fglt-b no no-planned-board available 0
lt:1/1/7 empty no no-error not-installed 0
lt:1/1/8 empty no no-error not-installed 0
vlt:1/1/63 empty no no-error not-installed 0
vlt:1/1/64 empty no no-error not-installed 0
——————————————————————————–
slot count : 9
================================================================================
leg:isadmin>#
leg:isadmin>#
leg:isadmin>#
leg:isadmin>#
leg:isadmin># configure equipment slot lt:1/1/5 planned-type fglt-b unlock # ADD CARD # 01=5, 02=6
leg:isadmin>configure>equipment# exit all
leg:isadmin># configure pon interface 1/1/5/[1…16] admin-state up #enable PON ports #
leg:isadmin># configure pon interface 1/1/5/1 admin-state up
leg:isadmin># configure pon interface 1/1/5/2 admin-state up
leg:isadmin># configure pon interface 1/1/5/3 admin-state up
leg:isadmin># configure pon interface 1/1/5/4 admin-state up
leg:isadmin># configure pon interface 1/1/5/5 admin-state up
leg:isadmin># configure pon interface 1/1/5/6 admin-state up
leg:isadmin># configure pon interface 1/1/5/7 admin-state up
leg:isadmin># configure pon interface 1/1/5/8 admin-state up
leg:isadmin># configure pon interface 1/1/5/9 admin-state up
leg:isadmin># configure pon interface 1/1/5/10 admin-state up
leg:isadmin># configure pon interface 1/1/5/11 admin-state up
leg:isadmin># configure pon interface 1/1/5/12 admin-state up
leg:isadmin># configure pon interface 1/1/5/13 admin-state up
leg:isadmin># configure pon interface 1/1/5/14 admin-state up
leg:isadmin># configure pon interface 1/1/5/15 admin-state up
leg:isadmin># configure pon interface 1/1/5/16 admin-state up
leg:isadmin>#
leg:isadmin># configure equipment slot lt:1/1/6 planned-type fglt-b unlock # ADD CARD # 01=5, 02=6
leg:isadmin>configure>equipment>slot>lt:1/1/6# exit all
leg:isadmin># configure pon interface 1/1/6/[1…16] admin-state up #enable PON ports #
leg:isadmin># configure pon interface 1/1/6/1 admin-state up
leg:isadmin># configure pon interface 1/1/6/2 admin-state up
leg:isadmin># configure pon interface 1/1/6/3 admin-state up
leg:isadmin># configure pon interface 1/1/6/4 admin-state up
leg:isadmin># configure pon interface 1/1/6/5 admin-state up
leg:isadmin># configure pon interface 1/1/6/6 admin-state up
leg:isadmin># configure pon interface 1/1/6/7 admin-state up
leg:isadmin># configure pon interface 1/1/6/8 admin-state up
leg:isadmin># configure pon interface 1/1/6/9 admin-state up
leg:isadmin># configure pon interface 1/1/6/10 admin-state up
leg:isadmin># configure pon interface 1/1/6/11 admin-state up
leg:isadmin># configure pon interface 1/1/6/12 admin-state up
leg:isadmin># configure pon interface 1/1/6/13 admin-state up
leg:isadmin># configure pon interface 1/1/6/14 admin-state up
leg:isadmin># configure pon interface 1/1/6/15 admin-state up
leg:isadmin># configure pon interface 1/1/6/16 admin-state up
leg:isadmin># admin save #save Config#
Writing configuration to /pub/IPD/dm/config.cfg
Saving configuration … OK
Completed.
leg:isadmin>#admin equipment reboot-isam with-self-test #reload#